View P0640EA70_914836.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

2 teccor electronics, inc. general information the teccor sidactor is a solid state transient voltage protector designed for use in telephony, data, and some ac applications. the sidactor is a bidirectional device that is normally connected to the high side of a circuit and a common. the sidactor remains in a high off-state impedance (leakage current <5 m a) until it senses a voltage exceeding its voltage breakover (v bo ). upon sensing an overvoltage, the sidactor will clamp the voltage and transition through a positive or negative zener region until enough current is present to allow the device to crowbar into a low impedance state. the typical voltage drop across the device during full conduction is typically less than 5 volts. the sidactor will return to its high impedance state when the current is interrupted or falls below the minimum holding current of the device. sidactor performance does not degrade with time, bias, number of operations or surges within the devices peak pulse current rating. it should be noted that the sidactor will fail short if the device is subjected to a surge that exceeds its rated peak pulse current (i pp ) or peak one cycle surge current (i tsm ). sidactors are available in breakdown voltages ranging from 30 to 540 volts and peak pulse current ratings up to 500 amps (2x10 m s). tape-and-reel packaging is available for the to-92 and to-220 packages along with embossed carrier reel packing for the do-214aa. please consult the factory for more information. features ? bidirectional transient voltage protection ? ion implant technology ? breakover voltages from 27 - 540 volts ? clamping speeds of nanoseconds ? patented multi chip packages ? electrically isolated package ? robust surge current capabilities ? glass-passivated junctions
teccor electronics, inc. 3 electrical parameter terminology v bo ? breakover voltage v bo (min) ? minimum voltage point at which the sidactor may begin to conduct v bo (max) ? maximum voltage required to begin conduction i bo ? breakover current current through the sidactor at the breakover point (v bo ) i pp ? peak pulse current maximum rated impulse current i tsm ? peak one cycle surge current sidactor?s maximum one cycle ac surge current rating i t ? on-state current continuous on-state current rating of the sidactor v t ? on-state voltage voltage drop across the device at rated on-state current i h ? holding current minimum current required to maintain the sidactor in the on state c o ? off-state capacitance sidactors typical off-state capacitance di/dt ? critical rate-of-rise on-state current maximum rated rate-of-rise current v f ? forward voltage maximum forward voltage across the p0641sa sidactor while in the on state (see figure 3c on page 13.)
4 teccor electronics, inc. ordering information part number definition package type description packing quantity added suffix optional industry standard to-92 bulk pack 2000 standard none tape and reel pack 2000 rp option eia rs-468-a tape and ammo pack 2000 ap option eia rs-468-a to-220 bulk pack 500 standard none clear plastic magazine or tube pack 50 tp option none tape and reel pack 700 rp option eia rs-468-a tape and reel pack for type 61 leadform 700 rp option eia rs-468-a do-214aa embossed carrier reel pack 2500 rp standard eia-481-1 bulk pack 5000 option none device packing options detailed packaging drawings are available from the factory upon request. *standard lead spacing is .200" for to-92 reel pack. for other spacing requirements please contact the factory.
teccor electronics, inc. 5 testing quality assurance 100% testing is a constant monitor for quality assurance. test description condition comments 1. surge (i pp ) @ rated current repeated 2 times in the normal se- quence of testing, except for to-220 which is repeated 4 times. 2. breakover voltage (v bo ) v bo and absolute peak in forward and reverse directions all devices fully characterized on voltage to ensure proper operation and reliability 3. holding current (i h ) measured for a minimum value as rated this ensures proper delatch (turn- off) after surge current condition. 4. peak on-state voltage (v tm ) measured with 1 amp rms or dc current 5. leakage current (i drm ) breakover leakage and off-state leakage these tests ensure long term reliability.
6 teccor electronics, inc. electrical specifications p a c k a g e t y p e package part number v bo i bo i pp i tsm breakover voltage (instantaneous clamping voltage) (1)(3)(13) volts break- over current peak pulse current t j 150c (5) (10) amps peak one cycle (sinusoidal) surge current (14) amps pins 1 to 3 m amps 2x10 m s 10x160 m s 10x560 m s 10x1000 m s min max max max max max max 60hz 50hz e t y p e 7 0 p0300ea70 27 36 10 100 50 50 30 25 P0640EA70 58 70 10 150 75 75 30 25 p0720ea70 65 80 10 150 75 75 30 25 p0800ea70 75 95 10 150 75 75 30 25 p1100ea70 90 125 10 100 50 50 30 25 p1300ea70 120 145 10 100 50 50 30 25 p1500ea70 140 170 10 100 50 50 30 25 p2300ea70 (12) 190 265 10 100 50 50 30 25 p2600ea70 (12) 220 300 10 100 50 50 30 25 p3100ea70 (12) 275 350 10 100 50 50 30 25 p3500ea70 (12) 300 400 10 100 50 50 30 25 b t y p e 7 0 p2300ba70 (12) 190 265 10 150 100 100 60 50 p2600ba70 (12) 220 300 10 150 100 100 60 50 p3100ba70 (12) 275 350 10 150 100 100 60 50 p3500ba70 (12) 300 400 10 150 100 100 60 50 p1500ec70 (12) 140 170 10 500 200 100 100 60 50 general notes ? all measurements are made at 60hz with a resistive load at an ambient temperature of +25 c unless otherwise specified. ? storage temperature range (t s ) is -65 o c to a +150 o c. ? the case temperature (t c ) is measured as shown on the dimensional outline drawings. see ?package dimensions? section. ? junction temperature range (t j ) is -40 c to +150 c on all devices except for p0300ea70, p0300sa and p0602aa where t j is -40 c to +125 c. ? the maximum lead solder temperature (for any soldering process) is +230c for 10 seconds maximum: _ > 1/16" (1.59mm) from case. ? all sidactors are bidirectional and all electrical parameters apply to both the forward and reverse polarities. ? all sidactors are recognized under ul 497b ?protectors for data communications and fire alarm circuits?, ul file #e133083. ? all sidactor leads are tin/lead plated with no less than 5% lead content. ? all sidactors meet the surge requirements of the following standards: electrical isolation teccor's electrically isolated to-92 and modified to-220 sidac- tor will withstand a high potential test of 1600 vac rms from leads to case over the operating temperature range. ccitt k17 - k20 10/700 m s 1.5 kv 5/310 m s 38 a vde 0433 10/700 m s 2 kv 5/200 m s 50 a cnet 0.5/700 m s 1.5 kv 0.2/310 m s 38 a
teccor electronics, inc. 7 electrical specifications i t i h v t c o di/dt continuous on- state dc or rms current (6)(15) amps holding current (2) mamps peak on-state voltage i t = 1 amp (17) volts off-state capacitance at 1khz 1vac with 50vdc bias (4) pf off-state capacitance at 1mhz 15mvac with 50vdc bias (4) critical rate of rise of on-state current amps/ m s pf max min max typ typ max 1.0 50 5.0 90 90 100 1.0 150 5.0 70 70 100 1.0 150 5.0 70 70 100 1.0 150 5.0 70 70 100 1.0 150 5.0 50 50 100 1.0 150 5.0 45 45 100 1.0 150 5.0 35 35 100 1.0 150 5.0 50 50 100 1.0 150 5.0 40 40 100 1.0 150 5.0 40 40 100 1.0 150 5.0 40 40 100 1.0 150 5.0 50 50 100 1.0 150 5.0 40 40 100 1.0 150 5.0 40 40 100 1.0 150 5.0 40 40 100 1.0 150 5.0 45 45 100 see referenced device application notes for device recommendations application description application note fcc part 68 connection of terminal equipment to the tele- phone network an1010 an1011 ul 1459 telephone equipment safety an1010 an1011 bellcore tr-nwt-001089 compatibility and safety for network telecommu- nications equipment an1012 bellcore tr-nwt-000974 telecommunications primary line protector units for central office and station call factory for assistance slic subscriber line interface circuit an1013 ptc using ptcs to pass fcc part 68 and ul145 an1020 isdn isdn u & t interfaces an1025 t1 t1 digital line card an1023 applications guide
8 teccor electronics, inc. electrical specifications v bo i bo i pp i stm p a c k a g e t y p e package part number breakover voltage volts break- over current m amps peak pulse current t j 150c (5) (10) amps peak one cycle (sinusoidal) surge current (14) amps 2x10 m s 10x160 m s 10x560 m s 10x1000 m s min max min max max max max 60hz 50hz s p0300sa 27 36 10 100 50 50 30 25 p0640sa 58 70 10 150 75 75 30 25 p0641sa (16) 58 70 10 150 75 75 30 25 p0720sa 65 80 10 150 75 75 30 25 p0800sa 75 95 10 150 75 75 30 25 p1100sa 90 125 10 100 50 50 30 25 p1300sa 120 145 10 100 50 50 30 25 p1500sa 140 170 10 100 50 50 30 25 p2300sa (11) 190 265 10 100 50 50 30 25 p2600sa (11) 220 300 10 100 50 50 30 25 p3100sa (11) 275 350 10 100 50 50 30 25 p3500sa (11) 300 400 10 100 50 50 30 25 p2300sb (11) 190 265 10 150 100 100 60 50 p2600sb (11) 220 300 10 150 100 100 60 50 p3100sb (11) 275 350 10 150 100 100 60 50 p3500sb (11) 300 400 10 150 100 100 60 50 p1500sc (11) 140 170 10 500 200 100 100 60 50 standardized part number symbolized part number p0300sa p03a p0640sa p06a p0641sa p61a p0720sa p07a p0800sa p08a p1300sa p13a p1500sa p15a p1500sc p15c p2300sa p23a p2300sb p23b p2600sa p26a p2600sb p26b p3100sa p31b p3100sb p31b p3500sa p35a p3500sb p35b notes to electrical specifications 1. see figure 4. for v bo change vs. junction temperature. 2. see figure 2. for i h vs case temperature. 3. all devices have a negative resistance slope unless otherwise noted. negative resistance slope devices v b0 is measured at an applied rate-of-rise of voltage 1 kv/sec. see figure 3a for v-i characteristics. 4. capacitance imbalance between forward and reverse polarities is typically 15 pf. 5. see figure 1 (a, b, c) for pulse wave form. 6. maximum t c is 110 c for to-92 and 115 c for modified to-220, except maximum t c is 75 c for p0300sa, p0300ea70 and 95 c for p0602aa. 7. during simultaneous surging of pins 1 & 3, the current rating of pin 2 doubles (2x). 8. between pins 2 to 1 and pins 2 to 3. 9. between any two pins. note: on the do-214 package, date code is located below the symbolized part number. to-92 and to-220 devices have full part numbers and a date code printed on the part. do-214 part numbers and part markings
teccor electronics, inc. 9 electrical specifications 10. the current wave virtual front duration is 1.25x rise time from 10% to 90% of crest. virtual zero is defined as the intersection with zero axis of a straight line drawn through points on the front of the current wave of 10% and 90% crest. waveforms defined per ieee/ansi c62.1. 11. see figure 3b for v-i characteristics. 12. 260ma minimum i h is available from the factory on special request. 13.the ul497b rate-of-rise of voltage requirements for v b0 testing is 100v/s, 100v/ m s, 500v/ m s, and 1kv/ m s. all sidactors v b0 's to be 10% of ratings. 14. for more than one full cycle rating, see figure 7. 15. thermal resistance: 16. see figure 3c for v-i characteristics. 17. see figure 5. 18. see figure 6. pxxxsa do214-aa r q jc = 28 c/watt and r q ja = 90 c/watt pxxxsb do214-aa r q jc = 26 c/watt and r q ja = 85 c/watt pxxxea70 to-92 r q jc = 28 c/watt and r q ja = 90 c/watt pxxxba70 to-92 r q jc = 26 c/watt and r q ja = 85 c/watt pxxxaa to-220 r q jc = 12 c/watt and r q ja = 50 c/watt pxxxab to-220 r q jc = 12 c/watt and r q ja = 50 c/watt i t i h v f v t c o di/dt continuous on-state dc or rms current (6)(15) amps holding current (2) mamps forward voltage drop volts peak on-state voltage i t = 1 amp (17) volts off-state capacitance at 1khz 1vac with 50vdc bias (4) pf off-state capacitance at 15mvac with 50vdc bias (4) pf critical rate of rise of on-state current amps/ m s max min max typ typ max 1.0 50 5.0 90 90 100 1.0. 150 5.0 70 70 100 1.0 150 5.0 5.0 40 113 100 1.0 150 5.0 70 70 100 1.0 150 5.0 70 70 100 1.0 150 5.0 50 50 100 1.0 150 5.0 45 45 100 1.0 150 5.0 35 35 100 1.0 150 5.0 50 50 100 1.0 150 5.0 40 40 100 1.0 150 5.0 40 40 100 1.0 150 5.0 40 40 100 1.0 150 5.0 50 50 100 1.0 150 5.0 40 40 100 1.0 150 5.0 40 40 100 1.0 150 5.0 40 40 100 1.0 200 5.0 42 40 100
10 teccor electronics, inc. electrical specifications p a c k a g e t y p e package part number v bo i bo i pp i tsm breakover voltage (instantaneous clamping voltage) (1)(3)(13) volts break- over current m amps peak pulse current t j 150c (5) (10) amps peak one cycle (sinusoidal) surge current (14) amps pins 1 to 3 pins 3 to 2 1 to 2 2x10 m s (7) 10x160 m s (7) 10x560 m s (7) 10x1000 m s (7) min max min max max min max max max 60hz 50hz a t y p e 6 1 p2000aa61 190 215 10 100 50 50 30 25 p2200aa61 205 230 10 100 50 50 30 25 p2400aa61 220 250 10 100 50 50 30 25 p2500aa61 240 280 10 100 50 50 30 25 p3000aa61 270 330 10 100 50 50 30 25 p3300aa61 300 360 10 100 50 50 30 25 a p0602aa 54 72 27 36 10 100 50 50 30 25 p1602aa 120 190 60 95 10 100 50 50 30 25 p2202aa 190 250 95 125 10 100 50 50 30 25 p2702aa 240 300 120 150 10 100 50 50 30 25 p3002aa 280 320 140 160 10 100 50 50 30 25 p4802aa (11) 440 580 220 290 10 100 50 50 30 25 p6002aa (11) 540 720 270 360 10 100 50 50 30 25 p1602ab 120 190 60 95 10 150 100 100 60 50 p2202ab 190 250 95 125 10 150 100 100 60 50 p2702ab 240 300 120 150 10 150 100 100 60 50 p3002ab 280 320 140 160 10 150 100 100 60 50 p4802ab(11) 440 580 220 290 10 150 100 100 60 50 p6002ab(11) 540 720 270 360 10 150 100 100 60 50 p1553aa 140 170 140 170 10 100 50 50 30 25 p2103aa 180 240 180 240 10 100 50 50 30 25 p2353aa 210 265 210 265 10 100 50 50 30 25 p2703aa 240 300 240 300 10 100 50 50 30 25 p3203aa 280 350 280 350 10 100 50 50 30 25 p3403aa 300 380 300 380 10 100 50 50 30 25 p1553ab 140 170 140 170 10 150 100 100 60 50 p2103ab 180 340 180 240 10 150 100 100 60 50 p2353ab 210 265 210 265 10 150 100 100 60 50 p2703ab 240 300 240 300 10 150 100 100 60 50 p3203ab 280 350 280 350 10 150 100 100 60 50 p3403ab 300 380 300 380 10 150 100 100 60 50 p3002ac 270 330 135 165 10 500 200 100 150 60 50 p3202ac 280 350 280 350 10 500 200 100 150 60 50
teccor electronics, inc. 11 electrical specifications i t i h v t c o di/dt continu- ous on- state dc or rms current (6) amps holding current (2) (9) mamps peak on-state voltage i t =1amp (18) volts off-state capacitance at 1khz 1vac with 50 vdc bias (4) pf off-state capacitance at 1mhz 15mvac with 50 vdc bias (4) pf critical rate of rise of on-state current amps/ m s pins 3 to 2 1 to 2 pins 1 to 3 pins 3 to 2 1 to 2 pins 1 to 3 pins 3 to 2 1 to 2 pins 1 to 3 max min max max typ typ max 1.0 150 10.0 30 30 100 1.0 150 10.0 30 30 100 1.0 150 10.0 30 30 100 1.0 150 10.0 30 30 100 1.0 150 10.0 25 25 100 1.0 150 10.0 25 25 100 1.0 50 5.0 10.0 90 45 90 45 100 1.0 150 5.0 10.0 140 85 140 85 100 1.0 150 5.0 10.0 50 30 50 30 100 1.0 150 5.0 10.0 45 30 45 30 100 1.0 150 5.0 10.0 40 25 40 25 100 1.0 200 (12) 5.0 10.0 50 35 50 35 100 1.0 200 (12) 5.0 10.0 50 30 50 30 100 1.0 200 (12) 5.0 10.0 140 85 140 85 100 1.0 200 (12) 5.0 10.0 90 60 90 60 100 1.0 200 (12) 5.0 10.0 80 50 80 50 100 1.0 200 (12) 5.0 10.0 75 45 75 45 100 1.0 200 (12) 5.0 10.0 50 35 50 35 100 1.0 200 (12) 5.0 10.0 50 30 50 30 100 1.0 150 10.0 10.0 50 40 50 40 100 1.0 150 10.0 10.0 45 35 45 35 100 1.0 150 10.0 10.0 40 30 40 30 100 1.0 150 10.0 10.0 35 25 35 25 100 1.0 150 10.0 10.0 50 40 50 40 100 1.0 150 10.0 10.0 50 40 50 40 100 1.0 200 (12) 10.0 10.0 100 80 100 80 100 1.0 200 (12) 10.0 10.0 80 60 80 60 100 1.0 200 (12) 10.0 10.0 70 55 70 55 100 1.0 200 (12) 10.0 10.0 60 50 60 50 100 1.0 200 (12) 10.0 10.0 50 40 50 40 100 1.0 200 (12) 10.0 10.0 50 40 50 40 100 1.0 200 (12) 5.0 10.0 45 30 45 30 100 1.0 200 (12) 5.0 10.0 40 30 40 30 100
12 teccor electronics, inc. electrical specifications figure 2 - normalized dc holding current vs case temperature figure 1c - pulse wave form (10 x 160 m s) figure 3a - v-i characteristics of devices with negative resistance figure 3b - v-i characteristics of devices with positive switching slopes figure 1b - pulse wave form (10 x 560 m s) figure 1b - pulse wave form (10 x 560 m s) figure 1a - pulse wave form (10 x 1000 m s)
teccor electronics, inc. 13 electrical specifications figure 3c - v-i characteristics of devices with a forward diode and reverse negative resistance figure 4 - normalized v bo change vs junction temperature figure 5 - peak on-state voltage vs peak on-state current for do-214aa and to-92 (typical) figure 7 - peak surge on-state current vs surge current duration figure 6 - peak on-state voltage vs peak on-state current for modified t0-220, pins 1 to 3 (typical)
14 teccor electronics, inc. electrical specifications

▲Up To Search▲

Price & Availability of P0640EA70

	To Download P0640EA70 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .